|
|
|
|
|
|
|
|
|
|
|
|
|
|
Used to secure the position of rebar during concrete pouring.
|
Designed for use in foundation construction, concrete forms and post reinforcement. ASTM A615-14 Grade 40.
|
Safely and easily twists wire bar ties. Plastic handle. Rugged design. Compact size allows the tool to be used in tight space.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Safely and easily twists wire bar ties. Hardwood handle, Ergonomic design.
|
Stanley Weldable Rebar, 1/2 in, NO 4 Nominal, 36 in Overall Length, Steel
|
Makes tying fast and easy. Wood handle.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Used by homeowners and residential contractors to create everything from lamp post and mailbox bases to deck supports. Easy-to-use cardboard tube, scaled-down version of rigid fiber forms that heavy-construction contractors use. Pour concrete in form, let it dry, then cut away form. Length can be cut down if needed.
|
Stanley Weldable Rebar, 1/2 in, NO 4 Nominal, 4 ft Overall Length, Steel, Used in Landscaping
|
Used by homeowners and residential contractors to create everything from lamp post and mailbox bases to deck supports. Easy-to-use cardboard tube, scaled-down version of rigid fiber forms that heavy-construction contractors use. Pour concrete in form, let it dry, then cut away form. Length can be cut down if needed.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Stanley Weldable Rebar, 1/2 in, NO 4 Nominal, 72 in Overall Length, Steel, Used in Landscaping
|
Nozzle kit for Ultrabond epoxy 22 oz. system. Hi-Flow nozzles reduce waste while increasing flow. 15 inch length snaps off to 10 inches if required. 3/8 diameter at tip. Built in mixing nut allows for fast and easy attachment to cartridge.
|
Used by homeowners and residential contractors to create everything from lamp post and mailbox bases to deck supports. Easy-to-use cardboard tube, scaled-down version of rigid fiber forms that heavy-construction contractors use. Pour concrete in form, let it dry, then cut away form. Length can be cut down if needed.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Unique forming process develops high cross strength. Ample load-bearing capacity. Stiff in service. Free from sagging or buckling. All lintels should be shored until mortar has cured. Coated with black corrosion-resistant paint. Made in USA.
|
Unique forming process develops high cross strength. Ample load-bearing capacity. Stiff in service. Free from sagging or buckling. All lintels should be shored until mortar has cured. Coated with black corrosion-resistant paint. Made in USA.
|
Unique forming process develops high cross strength. Ample load-bearing capacity. Stiff in service. Free from sagging or buckling. All lintels should be shored until mortar has cured. Coated with black corrosion-resistant paint. Made in USA.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Fastest, easiest way to form concrete footings; patented square footing form decreases cycle time, labor and material cost; can be sized, attached to construction tube, placed in excavated hole and backfilled. Can be used with rebar to reinforce footing or column if needed.
|
Use for anchoring and doweling. Long working time with a quick cure time. Moisture insensitive, can be used in underwater environments, concrete, hollow block, brick, clay and stone. Ideal for vertical, horizontal, and screen applications, seismic anchoring and bracing, surface crack repair. Ultra high-strength epoxy mixes through a static mixing tube and can also be resealed which means that any remaining material can be saved for later use. Cartridge w/nozzle.
|
Two component (1:1 ratio), 100-percent solids, high aspect ceramic blend, solvent-free, non-sag, high strength, high modulus, moisture insensitive epoxy system. Ideal for use as a bonding agent for almost any material, including metal, concrete, brick, wood, stone, block and other substrates. Can also be used for repairing holes, spalls, cracks in concrete, repairing rotted wood, installing and repairing anchor bolts or hand rails. LIMITATIONS: Minimum substrate and ambient temperature 40 degrees F (4.44 degrees C), Cartridge with two nozzles; medium duty caulking tool required.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Use for supporting sagging floors, weak beams and warping stairways. 2-1/4" x 15 gauge prime steel inner tubing. 2-1/2" x 15 gauge prime steel outer tubing. 2-1/4" steel collar. 1" x 6" steel screw. Two 4" x 4" x 10 gauge steel plates. 7" turning handle. Grooved pin and plain pin. Flow coated with red corrosion-resistant paint. Packed with instructions. UPC symbol on carton. Maximum load capacity obtained at lowest extension.
|
Fastest, easiest way to form concrete footings; patented square footing form decreases cycle time, labor and material cost; can be sized, attached to construction tube, placed in excavated hole and backfilled. Can be used with rebar to reinforce footing or column if needed.
|
Used to hold rebar off grade and centered in the foundation trench.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Used to support rebar rods when pouring concrete foundation or slab.
|
Made of lightweight durable plastic to give many years of trouble free use. Fits any standard size belt. Accomodates all types of tie wire.
|
Two component (1:1 ratio), 100 percent solids, high modulus, structural epoxy gel. It is a solvent free, low odor high strength, moisture insensitive, non-sag epoxy system. The resin and hardener are uniformly dispensed from a dual cartridge system and mixed simultaneously through a mixing nozzle or available in bulk. Long working time with a full cure in 24 hours. Moisture insensitive, may be used in damp environments, concrete, hollow block, brick, clay and stone. Ideal for vertical, horizontal, and screen applications. Structural bonding of concrete to concrete. Meets ASTM C881-14: Type I, II, IV and V, Grade 3, Class B and C. Cartridges with Nozzle.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Use for anchoring and doweling. Long working time with a quick cure time. Moisture insensitive, can be used in underwater environments, concrete, hollow block, brick, clay and stone. Ideal for vertical, horizontal, and screen applications, seismic anchoring and bracing, surface crack repair. Ultra high-strength epoxy mixes through a static mixing tube and can also be resealed which means that any remaining material can be saved for later use. Cartridge w/nozzle.
|
Use for supporting sagging floors, weak beams and warping stairways. 2-1/4" x 15 gauge prime steel inner tubing. 2-1/2" x 15 gauge prime steel outer tubing. 2-1/4" steel collar. 1" x 6" steel screw. Two 4" x 4" x 10 gauge steel plates. 7" turning handle. Grooved pin and plain pin. Flow coated with red corrosion-resistant paint. Packed with instructions. UPC symbol on carton. Maximum load capacity obtained at lowest extension.
|
Unique forming process develops high cross-sectional strength. Ample load-bearing capacity. Stiff in service. Free from sagging or buckling. All lintels should be shored until mortar has cured. Coated with black corrosion-resistant paint. 7" width. For 8" block. Made in USA.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Pre-formed bolt designed for anchoring to concrete in all construction work. Hold securely and permanently because of the angle design. Designed for all types of anchoring to poured concrete.
|
Use for supporting sagging floors, weak beams and warping stairways. 2-1/4" x 15 gauge prime steel inner tubing. 2-1/2" x 15 gauge prime steel outer tubing. 2-1/4" steel collar. 1" x 6" steel screw. Two 4" x 4" x 10 gauge steel plates. 7" turning handle. Grooved pin and plain pin. Flow coated with red corrosion-resistant paint. Packed with instructions. UPC symbol on carton. Maximum load capacity obtained at lowest extension.
|
Used for securing wood and metal forms to the ground in all flatwork applications, for attaching screed bard holder clamps, for securing landscape timbers, surveying stakes, string line guides, etc.
|
|
|
